I asked ChatGPT about BNB as the fate of CZ
Aug 31, 2023GM Recall: More Than 40,000 Chevrolet Silverado Medium
Aug 25, 2023Why climate tech investing slowed down in Q1
Aug 27, 2023Force Control Industries releases Magnashear motor brake for wind industry
Aug 14, 2023How to change the disc brake pads on your bike
Aug 05, 2023After the storm post
The devastating floods in Florida resulting from Hurricane Ian will require massive relief and rebuilding efforts — many of which depend on the trucking industry and thousands of truck drivers.
For commercial vehicles exposed to these types of floodwaters, Bendix has produced a number of technical tips for fleets and drivers on inspecting and possibly reconditioning air brake, wheel-end, and other safety components that have been partially or completely submerged.
The first determination to make is whether the water affecting the vehicle was salt water or fresh water. If it was salt water, you’ll need to immediately begin replacing parts due to its extreme corrosivity, which can remove lubrication and put certain parts at much higher risk for unexpected and premature malfunction. Bendix says any brake system valve that has been submerged in salt water must be replaced. In addition, systems and components including air compressors, air reservoirs, antilock brake system (ABS) relays, modulators, and brake actuators must also be replaced.
“Saltwater corrosion is also a threat to wheel-ends, since it increases the likelihood of rust jacking and accelerates corrosion of critical surfaces,” says Randy Salvatora, engineering manager – Vehicle Systems. “So, we recommend complete replacement of the foundation brakes to prevent a potential future failure. And if it’s not clear whether the water was fresh or salt, play it safe and follow the saltwater guidelines.”
Additionally, when replacing any pneumatic system components that have been subjected to flood conditions, disconnect all contaminated air tubes and hoses, flush them with clean water, and blow them out with air pressure to remove contaminants.
If you’re certain the power unit or trailer was submerged in fresh water, begin by carefully power-washing the vehicle — including the foundation brakes. Bendix says be cautious while cleaning: Rubber parts and sealing interfaces should not be directly sprayed with the high-pressure jet. Irreparable damage to valves will occur when a high-pressure washer directly sprays exhaust ports.
Appropriate PPE (Personal Protective Equipment) is recommended while washing or working on flooded vehicles, whether salt water or fresh. In the unapplied state, most valves have the delivery open to atmosphere at the exhaust port, so if any exhaust port is submerged, the water has infiltrated the system and can lead to future malfunction.
Bendix says technicians should not attempt to start a vehicle if fresh water has entered the air compressor or dryer through the air system intakes.
Additionally, Bendix says to follow these steps to thoroughly check the various parts of the air brake system:
Vehicle valving
Charging system
Bendix says if you find signs of moisture or other contamination, all the pneumatic air brake components should be replaced: Once water or contaminants get into any of the air brake components, it’s impossible to completely clear the system without total disassembly. Consider also the guidance included in the TMC Recommended Practice 617A for contaminant elimination procedure for tractor, trailer, or dolly air brake systems.
Examine all wheel-ends for water, which increases the possibility of corrosion between drum brake lining material and the shoe table (rust jacking), and can also pool in drums when left standing, increasing the risk of corrosion. You will also need to check the integrity of the friction couple between the friction and disc or drum. Water-filled loading docks may not immediately come to mind as “flood events,” but can certainly have the same impact to some wheel-end components such as slack adjusters, Bendix says.
Remove any fittings and mounting stud nuts, and orient ports downward to verify that no water has entered brake chambers through the air lines. If water is present, replace the actuator. Follow the appropriate wheel-end relubrication procedures, including re-greasing slack adjusters.
Assess the braking/safety electronics components by using a tool to conduct a diagnostic download on systems such as ABS, ESC (electronic stability control), and collision mitigation controllers, including any front or side radar units. Electronics will validate through self-check in most cases: If the electronic control unit (ECU) is operable, it will check the necessary solenoids, sensor, harnesses, etc. Make sure to inspect the seven-pin electrical connector interface between the tractor and trailer as well.
For further detailed reference, Bendix references two tech bulletins are available in the Bendix Document Library at bendix.com that serve as valuable resources for getting tractors and trailers back into service after they’ve been submerged:
Finally, if your checks turn up no evidence of water or contamination, conduct a thorough test of the air brake system and ABS before returning the vehicle or trailer to service. Note that between the floodwaters and power-washing, it’s possible that ABS wheel speed sensors may have been moved from their normal position. Push them back into contact with the exciter ring by hand, and when the wheel turns, normal wheel-bearing play will adjust the sensor position, Bendix says.
“We recommend retesting and diagnostic checks of the electronic systems after the initial post-flood testing,” Salvatora says. “Additionally, make sure you’re following other vehicle and system manufacturers’ guidelines: Flooding can have bumper-to-bumper effects, and you can’t be too careful.”